EV Charger Test Adapters

The Fluke FLK-FEV300 test adapter kit includes FEV300/BASIC test adapter, FEV300-CON-TY2 plug, 1664 FC multifunction tester and soft carrying bag. This kit is designed to test function and safety of charging stations mode 3 for AC charging. Basic test adapter has separate phase indication by three LED lamps for easy check if voltage is present at the charging output. The adapter imitates an electric vehicle and opens up a charging cycle(activating voltage/current output), allowing you to conduct tests in combination with appropriate test instruments like an installation tester (for example the Fluke 1664 FC) and/or an oscilloscope (for example the Fluke 120B Series Industrial Scope Meter®). The Fluke 1664 FC allows safety measurements via the measuring terminals like: earth bond, insulation, loop/line impedance, and RCD trip test. With the FEV300 Adapter Kit, charging stations can be tested in accordance with IEC/EN 61851-1 and IEC/HD 60364-7-722 Simulation of CP error state “E” Simulation of PE error state “F” (Earth fault) FEV300/BASIC test adapter has Proximity Pilot (PP) state selector FEV300/BASIC test adapter has terminals for CP signal output to check communication protocol FEV300/BASIC test adapter has control Pilot (CP) state selector FEV300/BASIC test adapter has PE Pre-Test to check if possible hazard touch voltage is present

The Fluke Type 2 plug can be used with EV charging station type 2 with socket outlet or fixed cable and vehicle connector. 7P three-phase AC charging mode 3

The Fluke FLK-FEV300/KIT DE test adapter kit includes FEV300/BASIC test adapter, and FEV300-CON-TY2 plug. This kit designed to test function and safety of charging stations mode 3 for AC charging. The adapter imitates an electric vehicle and opens up a charging cycle (activating voltage/current output), allowing you to conduct tests in combination with appropriate test instruments like an installation tester (for example the Fluke 1664 FC) and/or an oscilloscope (for example the Fluke 120B Series Industrial ScopeMeter®). FEV300-CON-TY2 plug is suitable to IEC 62196-2 type 2 socket outlet or fixed cable with vehicle connector (type 2, 7P three-phase). With the FEV300 Adapter Kit, charging stations can be tested in accordance with IEC/EN 61851-1 and IEC/HD 60364-7-722 FEV300/BASIC test adapter provides simulation of PE error state “F” (Earth fault) FEV300/BASIC test adapter has Proximity Pilot (PP) state selector FEV300/BASIC test adapter has terminals for CP signal output to check communication protocol FEV300/BASIC test adapter has control Pilot (CP) state selector FEV300/BASIC test adapter has PE Pre-Test to check if possible hazard touch voltage is present

The Fluke FEV300 electric vehicle charging station test adapter simulates the presence of an electrical vehicle, allowing the user to conduct safety and functionality tests in combination with appropriate test instruments such as an installation multifunction tester, digital multi-meter or oscilloscope. Use the FEV300 for station installations and to verify the station is working properly after install, during periodic maintenance, or troubleshooting an if the station is not delivering the appropriate charge. Perform a variety of tests including ground fault checks, insulation of wires, voltage and duty cycle to see max current available for charging all in one adapter. The FEV300 is suitable for AC charging stations with charging mode 3 and connectors type 2 and type 1. Provides simulation of PE error state “F” (Earth fault) Proximity Pilot (PP) state selector Terminals for CP signal output to check communication protocol Control Pilot (CP) state selector PE Pre-Test to check if possible hazard touch voltage is present IP 54 rating - Dust and splashing water protected

The Fluke Type 1 plug is can be used with EV charging station type 1 with fixed cable and vehicle connector. 5P single-phase AC charging mode 3