| Enrgtech LTD

New items

OD8/13-NL, Ruland

Torque Discs Nylon discs (resilient) - help dampen vibration and noise,Acetal discs (backlash-free) - designed for precise applications requiring zero backlash and higher torque capacity Technical specification Size Code Maximum Angular Misalignment (deg.) Maximum Parallel Misalignment (mm) Maximum Axial Motion (mm) 13 0.5 0.1 0.05 19 0.5 0.1 0.1 25 0.5 0.1 0.1 33 0.5 0.1 0.15 41 0.5 0.1 0.15 51 0.5 0.1 0.2 57 0.5 0.1 0.2 Note Size 13 discs not suitable for use with clamp style couplings Ruland Oldham Style Couplings Paradrive™ couplings are ideal for motion control applications, especially those utilising stepper or servo motors. Their low inertia design is ideally suited to higher speed applications and where electrical isolation is also required. Small angular and axial misalignments may be accommodated. Securing: 13mm and 19mm anodised aluminium hubs are secured to the shafts with one set screw on each end. 33mm, 35mm and 41mm hubs have 2 set screws set 90° apart

Product Detail

New items

OD26/41-AT, Ruland

Torque Discs Nylon discs (resilient) - help dampen vibration and noise,Acetal discs (backlash-free) - designed for precise applications requiring zero backlash and higher torque capacity Technical specification Size Code Maximum Angular Misalignment (deg.) Maximum Parallel Misalignment (mm) Maximum Axial Motion (mm) 13 0.5 0.1 0.05 19 0.5 0.1 0.1 25 0.5 0.1 0.1 33 0.5 0.1 0.15 41 0.5 0.1 0.15 51 0.5 0.1 0.2 57 0.5 0.1 0.2 Note Size 13 discs not suitable for use with clamp style couplings Ruland Oldham Style Couplings Paradrive™ couplings are ideal for motion control applications, especially those utilising stepper or servo motors. Their low inertia design is ideally suited to higher speed applications and where electrical isolation is also required. Small angular and axial misalignments may be accommodated. Securing: 13mm and 19mm anodised aluminium hubs are secured to the shafts with one set screw on each end. 33mm, 35mm and 41mm hubs have 2 set screws set 90° apart

Product Detail

New items

VIVA-V150-ELEMENT, Rexnord

Rexnord Viva Elastomer Coupling This elastomeric coupling range from Rexnord is low maintenance requiring no lubrication. The soft polymer element is able to cope with, and correct for considerable mis-alignment. Two piece polymer element allow's for quick removal and replacement without the need to disturb the hubs, shaft or remove equipment from its mountings. Polyurethane element cushions connected components from vibration and shock. Suitable for a diverse range of applications including centrifugal compressors and blowers, metal extruders, cooling towers, reciprocating pumps and forced draft fans. ATEX approved. One complete coupling requires the purchase of two hubs and a polymer connecting element. Built in Overload Protection Close Coupled and Spacer Versions Available to Allow for Different Shaft Spacings For Applications up to 7,500 rpm Low Maintenance ATEX Elastomer Couplings

Product Detail

New items

ROTEX38-98SHEL-KTR, KTR

KTR Jaw Coupling Spiders Jaw coupling spiders for use with KTR's range of hubs. Manufactured from T-PUR® an improved polyurethane that is able to withstand significantly higher temperatures than standard polyurethane spiders giving greatly improved length of service. Available in 92 (shore-A), 98 (shore-A) and 64 (shore-D) for varying degrees of damping in various sizes to suit a wide variety of applications. ATEX approved. Note Each Coupling requires two hubs and a spider. KTR Jaw Couplings

Product Detail

New items

ROTEX38-92SHEL-KTR, KTR

KTR Jaw Coupling Spiders Jaw coupling spiders for use with KTR's range of hubs. Manufactured from T-PUR® an improved polyurethane that is able to withstand significantly higher temperatures than standard polyurethane spiders giving greatly improved length of service. Available in 92 (shore-A), 98 (shore-A) and 64 (shore-D) for varying degrees of damping in various sizes to suit a wide variety of applications. ATEX approved. Note Each Coupling requires two hubs and a spider. KTR Jaw Couplings

Product Detail

New items

ROTEX48-92SHEL-KTR, KTR

KTR Jaw Coupling Spiders Jaw coupling spiders for use with KTR's range of hubs. Manufactured from T-PUR® an improved polyurethane that is able to withstand significantly higher temperatures than standard polyurethane spiders giving greatly improved length of service. Available in 92 (shore-A), 98 (shore-A) and 64 (shore-D) for varying degrees of damping in various sizes to suit a wide variety of applications. ATEX approved. Note Each Coupling requires two hubs and a spider. KTR Jaw Couplings

Product Detail

New items

ROTEX19PB-ALIUB-KTR, KTR

KTR Jaw Couplings - Hub A range of hubs from KTR for use with the ROTEX range of jaw coupling spiders. Available in various sizes and in aluminium, steel and cast iron (dependant upon size). Hubs come pilot bored. ATEX approved. Note Each Coupling requires two hubs and a spider. KTR Jaw Couplings

Product Detail

New items

ROTEXGS9-64SHEL, KTR

The KTR ROTEX GS green coloured three part axial plug in vibration reducing jaw type coupling . Thus different hub designs and the different shore harnesses' offer the optimal coupling for each application in automation engineering. The coupling is used in machine tools, automation, power transmission, medical technology, packaging technology. Maintenance-free Electrically isolating Failsafe Backlash free

Product Detail

New items

PHE F90NRTYRE, SKF

The SKF flex coupling are designed to accommodate misalignment and shock loads and dampen vibration levels. It is easy to install, maintenance-free couplings are available with either a machined-to-size or tapered bore. These coupling are also available with a taper bushing and it consist of 2 flanges and 1 tyre. The flex tyres are available in natural rubber compounds for applications ranging from –50 to +50 °C. Chloroprene rubber compounds should be used in applications where exposure to greases and oils are likely. These compounds can accommodate temperatures ranging from –15 to +70 °C. The chloroprene tyres should be used where fire-resistance and anti-static (F.R.A.S.) properties are required. Coupling size 90 Used face and hub mounting

Product Detail

New items

OMEGA-E10-ELEMENT, Rexnord

Rexnord Omega Elastomer Couplings - Element E (Short) The Rexnord Omega E element is made from a unique general purpose elastomer with a split element design providing easy assembly. The design permits faster installation and reduced inventories by providing multiple distances between shaft ends using the same elements and hubs. The Rexnord Omega E design is used on close coupled applications. Features and Benefits Split in half element Torsionally soft Interchangeable hubs Easy installation Excellent vibration damping High misalignment capacity No lubrication required Application Information For use with pumps, compressors, industrial fans and mixers. Can operate in either horizontal or vertical applications without additional components. Elastomer Couplings

Product Detail

New items

OMEGA-E2-ELEMENT, Rexnord

Rexnord Omega Elastomer Couplings - Element E (Short) The Rexnord Omega E element is made from a unique general purpose elastomer with a split element design providing easy assembly. The design permits faster installation and reduced inventories by providing multiple distances between shaft ends using the same elements and hubs. The Rexnord Omega E design is used on close coupled applications. Features and Benefits Split in half element Torsionally soft Interchangeable hubs Easy installation Excellent vibration damping High misalignment capacity No lubrication required Application Information For use with pumps, compressors, industrial fans and mixers. Can operate in either horizontal or vertical applications without additional components. Elastomer Couplings

Product Detail

New items

ROTEX24-98SHEL-KTR, KTR

KTR Jaw Coupling Spiders Jaw coupling spiders for use with KTR's range of hubs. Manufactured from T-PUR® an improved polyurethane that is able to withstand significantly higher temperatures than standard polyurethane spiders giving greatly improved length of service. Available in 92 (shore-A), 98 (shore-A) and 64 (shore-D) for varying degrees of damping in various sizes to suit a wide variety of applications. ATEX approved. Note Each Coupling requires two hubs and a spider. KTR Jaw Couplings

Product Detail

Flexible Coupling Flectors

New Items

OD8/13-NL, Ruland

OD26/41-AT, Ruland

VIVA-V150-ELEMENT, Rexnord

ROTEX38-98SHEL-KTR, KTR

ROTEX38-92SHEL-KTR, KTR

ROTEX48-92SHEL-KTR, KTR

ROTEX19PB-ALIUB-KTR, KTR

ROTEXGS9-64SHEL, KTR

PHE F90NRTYRE, SKF

OMEGA-E10-ELEMENT, Rexnord

OMEGA-E2-ELEMENT, Rexnord

ROTEX24-98SHEL-KTR, KTR

FAQs