Shields For Arduino

New items

RFD22126, RFduino

RFduino Battery Shield Dual AAA Battery Shield The RFduino RFD22126 Dual AAA battery shield will need two AAA batteries (not supplied) for operation. A step up regulator is incorporated to offer a constant 3.3V output to the RFduino. · RFD22126 Dual AAA Battery: Batteries not included see products such as 448-8460 · Dimensions: L 77.47mm x W 25.4mm · Output voltage: 3.3V · Output Current: 100mA Single AAA Battery Shield The RFduino RFD22127 Single AAA battery shield will require an AAA type battery (not supplied) to perform. A step up regulator is incorporated to offer a constant 3.3V output to the RFduino. · RFD22127 Single AAA battery Shield: Batteries not included see products such as 448-8460 · Dimensions: L 75.69mm x W 22.86mm · Output voltage: 3.3V · Output Current: 40mA CR2032 Coin Battery Shield The RF Digital RFD22128 CR2032 Coin Battery Shield will require the CR2032 3V battery in order to run the RFduino. There is no need for a regulator and it will manage the RFduino devices. · Dimensions: L 46.99mm x W 22.86mm · Output voltage: 2V — 3V · Output Current: 25mA Bluetooth - RF Digital

Product Detail

New items

SHIELDBTS500151TADTOBO1, Infineon

The 12V Protected switch shield for Arduino comes with BTS50015-1TAD (RDS(ON) 1.5mΩ), an ultra-low ohmic smart high-side power switch from the Power PROFET™ family. Designed for relay and fuse replacement in power distribution and junction boxes, Power PROFET™ can drive resistive, capacitive and inductive loads (e.g. heating resistors, filter capacitors, motor, valves and pumps). Stand alone and microcontroller mode. Easy to use plug and play. Fully configurable for different kind of loads. Enables quick evaluation of Power PROFET™ for switching loads (BTS50015-1TAD: I NOM = 33 A). Fast prototyping for switching applications. Relay and fuse replacement in power distribution and junction boxes. Drive resistive, inductive and capacitive loads such as heating resistors, filter capacitors, motor, valves and pumps.

Product Detail

New items

CleO-RIO1, Bridgetek

CleO Reverse-I/O pins Adapter Shield The CleO-RIO is an adapter Shield that allows an Arduino processor board to be stacked on top of the CleO Smart TFT Display module. Note CleO Smart TFT display for Arduino is available under RS Part No. 124-1038 .

Product Detail

New items

ASX00021, Arduino

ARDUINO PORTENTA VISION SHIELD E

Product Detail

New items

DFR0763, DFRobot

SIM7000A ARDUINO NB-IOT EXPANSIO

Product Detail

New items

RFD22125, RFduino

RFduino Prototype shield The RF Digital RFD22125 Proto shield allows you to build your own prototype shield for the RFduino. There is a free grid area to enable you to add your own circuits; it also lets you access the 3V supply rail and ground. Dimensions: L 22.86mm x W 22.86mm Bluetooth - RF Digital

Product Detail

New items

SHIELDBTS70041EPZTOBO1, Infineon

683046 The Infineon's BTS7004-1EPZ is a Smart High-Side Power Switch that comes with Arduino shield, providing protection functions and diagnosis. The device is suitable for applications with extended or/and high temperature mission profiles. It is suitable for driving 15 A resistive, inductive and capacitive loads and replaces electromechanical relays, fuses and discrete circuits. For demonstrating relay and fuse replacement, the shield can be used to control and protect outputs of a 12V supply, turn ON/OFF loads (e.g. bulbs, heating resistors, motor drives), measure the load current and detect no-load condition. High-Side Switch with Diagnosis and Embedded Protection Part of PROFET™+2 12V Family Green Product (RoHS compliant) Qualified for automotive applications. Product validation according to AEC-Q100 Grade 0. Overcurrent protection (tripping) with Intelligent Latch Under voltage shutdown

Product Detail

New items

CY8CKIT-024, Infineon

CY8CKIT-024 CapSense Proximity Shield, Cypress Semiconductor The CY8CKIT-024 CapSense Proximity Shield is an Arduino-compatible evaluation platform for CapSense-based proximity sensing solutions. The shield is designed to work with the Cypress PSoC Pioneer kits (CY8CKIT-040 and CY8CKIT-042). The CY8CKIT-024 CapSense Proximity Shield enables you to evaluate the proximity sensing features including Liquid Tolerance, Wake-On-Approach and Gesture Detection. The kit is using 5 proximity loops. With the CY8CKIT-024 Shield, Cypress is providing users with three-dimensional gesture recognition capabilities for capacitive proximity sensing detection. Proximity-sensing distance of approximately up to 100 mm when interfaced with the CY8CKIT-040 or CY8CKIT-042 kits Horizontal and vertical gesture detection at a distance of 20 mm Liquid-tolerant proximity sensing Kit Contents CY8CKIT-024 CapSense Proximity Shield Quick Start Guide Water Dropper

Product Detail

New items

2501000101291, Wurth Elektronik

The Wurth Elektronik sensor shield for Arduino is stackable expansion board for Arduino UNO and Arduino DUE. It has I²C and SPI interface with 3.3 V and 5 V logic output. Quick start Compatible with 6-pin connector

Product Detail

New items

DPP902S000, TE Connectivity

The MEAS weather shield for ARDUINO/Genuino mother board provides the necessary hardware to interface the HTU21D digital relative humidity sensor, MS5637 digital barometric pressure sensor, temperature system sensor (TSYS01), MS8607 digital relative humidity and digital pressure sensor, TSD305-1C55 digital thermopile sensor, all from TE Connectivity (TE) to any system that utilizes ARDUINO/Genuino mother board compatible expansion ports configurable for I2C communication. The HTU21D sensor is a self-contained humidity and temperature sensor that is fully calibrated during manufacturing.

Product Detail

New items

CY15FRAMKIT-001, Cypress Semiconductor

CY15FRAMKIT-001 Serial F-RAM Development Kit (Arduino-Compatible) The CY15FRAMKIT-001 is an F-RAM (Ferroelectric RAM) development kit for high-performance, high-reliability and energy efficient serial F-RAM devices. The CY15FRAMKIT-001 kit has been designed to operate with the Arduino UNO R3 board with stackable connectors. Compatible with CY8CKIT-042, CY8CKIT-042-BLE and CY8CKIT-040 kits 256 Kbit SPI F-RAM and a 256 Kbit I²C F-RAM Power supply operation at 3.3 V or 5.0 V FRAM (Ferroelectric RAM) FRAM (Ferroelectric Random Access Memory) is a non-volatile memory that uses ferroelectric film as a capacitor for storing data. Possessing characteristics of both ROM and RAM devices, F-RAM features high-speed access, high endurance in write mode, low power consumption, non-volatility, and excellent tamper resistance. It is therefore ideal memory for use in smart cards which need high security and low power consumption, as well as cellular phones and other devices.

Product Detail

New items

CY8CKIT-024, Cypress Semiconductor

CY8CKIT-024 CapSense Proximity Shield, Cypress Semiconductor The CY8CKIT-024 CapSense Proximity Shield is an Arduino-compatible evaluation platform for CapSense-based proximity sensing solutions. The shield is designed to work with the Cypress PSoC Pioneer kits (CY8CKIT-040 and CY8CKIT-042). The CY8CKIT-024 CapSense Proximity Shield enables you to evaluate the proximity sensing features including Liquid Tolerance, Wake-On-Approach and Gesture Detection. The kit is using 5 proximity loops. With the CY8CKIT-024 Shield, Cypress is providing users with three-dimensional gesture recognition capabilities for capacitive proximity sensing detection. Proximity-sensing distance of approximately up to 100 mm when interfaced with the CY8CKIT-040 or CY8CKIT-042 kits Horizontal and vertical gesture detection at a distance of 20 mm Liquid-tolerant proximity sensing Kit Contents CY8CKIT-024 CapSense Proximity Shield Quick Start Guide Water Dropper Touch Screen Controllers

Product Detail

New Items

RFD22126, RFduino

SHIELDBTS500151TADTOBO1, Infineon

CleO-RIO1, Bridgetek

ASX00021, Arduino

DFR0763, DFRobot

RFD22125, RFduino

SHIELDBTS70041EPZTOBO1, Infineon

CY8CKIT-024, Infineon

2501000101291, Wurth Elektronik

DPP902S000, TE Connectivity

CY15FRAMKIT-001, Cypress Semiconductor

CY8CKIT-024, Cypress Semiconductor

FAQs