LCR Meter Accessories

What are the LCR Meter Accessories?

An LCR meter is a type of electronic measuring device utilized in industry to measure the inductance (L), capacitance (V), and resistance (R) of an electronic component. The impedance was measured internally in earlier iterations of this instrument and converted to the relevant capacitance or inductance value for display. Readings should be fairly accurate if the capacitor or inductor device being tested does not have a major resistive component of impedance.

How does the LCR Meter work?

The device being tested (DUT) is typically exposed to an AC power source. The meter monitors both the current flowing through and the voltage across the DUT. LCR Meter Accessories can calculate the impedance's magnitude from its ratio. In more sophisticated instruments, the phase angle between the voltage and current is also measured; when combined with the impedance, it is possible to calculate and display the equivalent capacitance, inductance, and resistance of the DUT.

What is an LCR Meter used for?

Impedance is a physical property that is measured using LCR meters, which are measuring equipment. The quantifier Z is used to express impedance, which is resistance to the passage of an AC current. It can be determined using the voltage V between the measurement target's terminals and the current flowing to it.

New Items

New items

TLKB1, BK Precision

The BK Precision 4 wire Kelvin clip test fixture minimizes the influence of the test lead resistance and improves measurement accuracy. Designed for BA6010 and BA6011

Product Detail

New items

16034G, Keysight Technologies

The Keysight Technologies 16034G this test fixture is designed for impedance evaluations of SMD. The minimum SMD size that this fixture is adapted to evaluate is 0.6 (L) x 0.3 (W) [mm]. Open and short compensations are recommended before measurement. When measuring above 3 MHz, load compensation is also recommended. Open compensation is performed by separating the high and the low electrodes from each other. The separation size should be equivalent to the DUTs width Short compensation is performed placing the high and low electrodes in contact together Load compensation is performed by using the furnished 100 Ω SMD chip resistor After performing open, short and load compensations, the DUT is inserted into the test fixture

Product Detail

New items

16048E, Keysight Technologies

The Keysight Technologies 16048E test leads extend the measurement port with a 4-Terminal Pair configuration. It is provided with a BNC female connector board to allow the attachment of user-fabricated test fixtures. Cable length compensation is recommended before measurement Set the instruments cable length compensation function to 4 m

Product Detail

New items

16089C, Keysight Technologies

The Keysight Technologies 16089C this test fixture makes it possible to measure odd-shaped components that cannot be measured with conventional fixtures. It is equipped with two insulated Kelvin clips. Open and short compensations are recommended before measurement For open compensation, do not connect the Kelvin clips to anything Short compensation is performed by connecting the Kelvin clips together After performing open and short compensations, the DUT is held with the Kelvin clips

Product Detail

New items

SMD03m, Peak Electronic Design

Peak LCR40m Passive Component Analyser The LCR40m will automatically identify inductors, capacitors and resistors, measuring the main component value and other componant details (e.g coil inductance and dc resistance). The LCR40m is ideal for unmarked and surface mount designs. Automatic component identification Automatic test frequency selection Delayed or instant analysis (for hands free operation) Non volatile probe and test lead compensation Automatic ranging and scaling with real units displayed Auto and manual power-off Resistance range 1Ω to 2MΩ resolution 0.3Ω min, 0.6Ω typ accuracy ±1% ± 1.2Ω Capacitance range 0.5pF → 10000μF resolution 0.2pF min, 0.5pF typ accuracy ±1.5% ± 1.0pF Inductance range 1μH → 10H resolution 0.4μH min, 0.8μH typ accuracy ±1.5% ± 1.6μH Peak test voltage ±1.05V Peak test current +3.2mA Auto power on/off.

Product Detail

New items

TL8KC1, BK Precision

The BK Precision 4 terminal shielded Kelvin test lead is useful for measuring leaded capacitors, inductors, and resistors. When used with 880, the guarded lead reduces the effect of lead impedances and contact resistance thus minimizing measurement errors and improving accuracy especially in the lower impedance range. It is an included accessory with the model 880. Cable length is approximately 16 in

Product Detail

New items

16034H, Keysight Technologies

The Keysight Technologies 16034H this test fixture is designed for impedance evaluations of array-type SMD. The minimum SMD size that this fixture is adapted to evaluate is 1.6(L) x 0.8(W) [mm]. Since the tip of the measurement electrodes are very thin and the device holder is extremely flat, the device can be shifted and the measurement electrodes can contact the each element of the array-type component. Open and short compensations are recommended before measurement When measuring above 3 MHz, load compensation is also recommended Open compensation is performed by separating the high and the low electrodes from each other The separation should be equivalent in size to the DUTs width Short compensation is performed by placing the high and low electrodes in contact together Load compensation is performed by using the furnished 100 Ω SMD chip resistor After performing open, short and load compensations, the DUT is inserted into the test fixture

Product Detail

New items

LLSm, Peak Electronic Design

Product Detail

New items

AMT 006, Aoip Instrumentation

AOIP OM 16 micro-ohmmeter Accessories A range of accessories for use with OM 16 micro-ohmmeter. Test Probe AMT 005 Mounted on metallic rod with handle 5 m cord and locking socket adapted to the OM 16 micro-ohmmeter Measurement is taken by pressing a point (voltage reading) mounted on a spring. This measurement is taken when the fixed concentric part (arrival of current) makes contact with the part to be measured. Kelvin Clamp / Clip AMT 006 Fitted with a 5 m cord and a locking socket adapted to the OM16 Permanently takes a current of 10 A

Product Detail

New items

U1780A, Keysight Technologies

Keysight U1701A & U1701B Handheld Capacitance Meter For electronics assembly and passive components troubleshooting. 11,000 counts resolution Dual display with backlight Wide measurement range 0.1pF to 199.99mF Compare mode with 25 sets of High/Low limit settings Tolerance mode 1%, 5%, 10% and 20% Relative mode Hold and Min/Max/Average recordings Capacitance Range Resolution Accuracy Measuring rate at Full Scale (approx) 1000.0 pF 0.1 pF ±(1% rdg +10 dig) 5 times/sec 10.000 nF 0.00 1nF ±(1% rdg +5 dig) 5 times/sec 100.00 nF 0.01 nF ±(0.5% rdg +3 dig) 5 times/sec 1000.0 nF 0.1 nF ±(0.5% rdg +3 dig) 5 times/sec 10.000 μF 0.001 μF ±(0.5% rdg +3 dig) 5 times/sec 100.00 μF 0.01 μF ±(0.5% rdg +3 dig) 5 times/sec 1000.0 μF 0.1 μF ±(0.5% rdg +3 dig) 0.86 times/sec 10.000 mF 0.001 mF ±(1% rdg +5 dig) 0.13 times/sec 199.99 mF 0.01 mF ±(2% rdg +5 dig) 0.36 times/min Accuracy given as ± (% of output + counts of least significant digit) at 23 °C ±5 °C, with relative humidity less than 80% RH Note One year calibration cycle recommended by manufacturer Supplied with quick start guide, product reference CD with user's & service guide and data logging software, certificate of calibration, alligator clip leads, 9V alkaline battery

Product Detail

New items

LCX-K107, Rohde & Schwarz

The Rohde & Schwarz digital I/O ports and binning function includes a trigger input and eight data lines for binning. With this function, the measurement results can be divided into up to eight tolerance ranges and the measured components sorted by their values into sorting containers installed by the customer. It has digital I/O ports and binning function It's implemented as a BNC connector The measurement results can be divided into up to eight tolerance ranges

Product Detail

New items

RS KML 7499 / PZ / RG174 / 100, Schutzinger

Schutzinger Kelvin Test Leads A comprehensive offering of Kelvin test leads, consisting of BNC to tweezer and lamella basket to pincer versions all of which have been developed for four wire measurement, assembled on RG174U cable and PVC cable where applicable, complete with gold plated contact parts. These Kelvin test leads form part of the Schutzinger Kelvin Program. Current rating 1A Voltage rating 33 Vac/70 Vdc

Product Detail

What are the LCR Meter Accessories?

How does the LCR Meter work?

What is an LCR Meter used for?

The difference between an LCR Meter and Multimeter

New Items

TLKB1, BK Precision

16034G, Keysight Technologies

16048E, Keysight Technologies

16089C, Keysight Technologies

SMD03m, Peak Electronic Design

TL8KC1, BK Precision

16034H, Keysight Technologies

LLSm, Peak Electronic Design

AMT 006, Aoip Instrumentation

U1780A, Keysight Technologies

LCX-K107, Rohde & Schwarz

RS KML 7499 / PZ / RG174 / 100, Schutzinger

FAQs