Loop & RCD Testers

New items

LRCD220-EN-BS, Megger

LRCD220 Loop & RCD Tester The LRCD200 series tester combines an Earth loop impedance tester with an RCD tester. The loop tester is a non-tripping test suitable for systems protected with 30mA or larger RCDs. The RCD testing supports 10mA to 1000mA RCDs with the full range of tests. Ramp testing provides a trip current test for the testing of nuisance tripping RCDs. Suitable for use on 110V or 3 phase supplies.,Designed to meet the tough environment of site work, the instruments are rubber armoured, have a built-in protective front cover, and meet the requirements of BS7671, IEC1010 and BSEN61557. All instruments are IP54 weatherproof. The combined instrument offers all the test functions necessary for live electrical testing requirements, in a simple and cost effective instrument. Built-in protective front cover Tough rubber armoured case Weatherproof to IP54 High current loop testing Phase to phase loop testing Auto RCD testing 1000mA RCD test Phase rotation 110V, 230V and 415V operation Backlit display Note RS is an authorised Megger distributor. Purchased though RS this product is eligible for the Megger extended 3 Year warranty Supplied with Durable hard carry case, instructions, 3 wire test lead with crocodile clips, BS1363 mains socket test lead, 8 off AA alkaline batteries.

Product Detail

New items

FC2000, Kewtech Corporation

Kewtech FC2000 Calibration Check Box The FC2000 Calibration Checkbox allows electricians to check their own 17th Edition test equipment and ensure that all meters are operating correctly and accurately. The Kewtech FC2000 Check Box doesn't replace the calibration requirements of testers but provides a quick and simple way to check instrument accuracy, reducing the risk of incorrect certification. Checks that 17th edition testers are maintaining their calibration Test lead nulling point Three continuity test points Three Insulation test points Two loop impedance test points plus the local loop 1/2, x 1, x 5 30mA current and time test settings Supplied with Mains lead, instruction manual.

Product Detail

New items

LTW315-RS-BS, Megger

LTW 300 Series Earth loop impedance testers to verify the loop impedance of a live electrical circuit without the need to disconnect the electrical supply. The LTW300 series instruments offer a safe and easy 2 wire loop testing solution that does not trip 30mA RCDs and can be used on a wide range of voltages. Backlit display 0.01Ω resolution No-trip loop test on circuits with RCDs of ≥30 mA 3 phase circuits with RCD protection can be tested Tests radial circuits where the circuit does not return to the origin, even where only a phase and neutral contacts are available. 10 second non trip loop test time with Auto test extension up to a further 10 seconds if noise is detected, to improve the accuracy of the test High current loop testing for supplies that do not have an RCD fitted AUTO START will start the loop test running as soon as the test leads are connected; no need to press the test button means much safer testing PFC Display up to 20kA Voltage and frequency measurement 110Vac systems including 110V centre tap to earth (55V phase to earth) can be tested on the secondary winding. IP54 Weatherproof case Optional 10A fused 2 wired test leads and crocodile clip set Complies with IEC61010-1 300V CATIV safety standard and meets EN61557 Voltage measurement (ac only) 50V to 440V Accuracy ±2% ±1V Range 25Hz to 99.99Hz Accuracy ±0.1Hz A warning will be shown if applied voltage exceeds 440V Damage will occur if applied voltage exceeds 600Vrms Loop testing No-trip loop and high current loop test Source voltage LTW315: 100V to 280V (50Hz) LTW325: 50V to 440V (50Hz) Display range 0.01Ω to 2000Ω Accuracy ±5% ±0.03Ω Nominal test current No-Trip loop test 15 mA (at nominal 230Vac supply) High current loop test 4 A (at nominal 230 Vac supply) Operational range 0.30Ω to 1000Ω Prospective Fault Current (PFC) Prospective fault current Measured Source Voltage / Loop resistance ...

Product Detail

New items

P06230304, Chauvin Arnoux

The Multimetrix VT11 is the wall plug tester and the rated voltage required for the device is the 230V. It have differential sensitivity up to 30 mA. Temperature range is 0 to 40 °C Relative humidity is < 80 % RH

Product Detail

New items

P06230301, Chauvin Arnoux

The Multimetrix VT35 is the socket tester for testing of differential circuit breakers from 10 to 35 mA. It detect no phase, no earth, no neutral, phase/neutral and phase/earth inversion. Easy and quick connection by 2P+T power socket

Product Detail

New items

LTW315-EU-BS, Megger

LTW 300 Series Earth loop impedance testers to verify the loop impedance of a live electrical circuit without the need to disconnect the electrical supply. The LTW300 series instruments offer a safe and easy 2 wire loop testing solution that does not trip 30mA RCDs and can be used on a wide range of voltages. Backlit display 0.01Ω resolution No-trip loop test on circuits with RCDs of ≥30 mA 3 phase circuits with RCD protection can be tested Tests radial circuits where the circuit does not return to the origin, even where only a phase and neutral contacts are available. 10 second non trip loop test time with Auto test extension up to a further 10 seconds if noise is detected, to improve the accuracy of the test High current loop testing for supplies that do not have an RCD fitted AUTO START will start the loop test running as soon as the test leads are connected; no need to press the test button means much safer testing PFC Display up to 20kA Voltage and frequency measurement 110Vac systems including 110V centre tap to earth (55V phase to earth) can be tested on the secondary winding. IP54 Weatherproof case Optional 10A fused 2 wired test leads and crocodile clip set Complies with IEC61010-1 300V CATIV safety standard and meets EN61557 Voltage measurement (ac only) 50V to 440V Accuracy ±2% ±1V Range 25Hz to 99.99Hz Accuracy ±0.1Hz A warning will be shown if applied voltage exceeds 440V Damage will occur if applied voltage exceeds 600Vrms Loop testing No-trip loop and high current loop test Source voltage LTW315: 100V to 280V (50Hz) LTW325: 50V to 440V (50Hz) Display range 0.01Ω to 2000Ω Accuracy ±5% ±0.03Ω Nominal test current No-Trip loop test 15 mA (at nominal 230Vac supply) High current loop test 4 A (at nominal 230 Vac supply) Operational range 0.30Ω to 1000Ω Prospective Fault Current (PFC) Prospective fault current Measured Source Voltage / Loop resistance ...

Product Detail

New items

LT300-EN-BS, Megger

LT300 Loop Tester The LT300 combines high current-loop testing over a wide range of frequencies and supply voltages with simple operation. This is a HIGH CURRENT ONLY tester, designed for installations where there are no RCDs installed. A two-wire test performs a fast loop impedance measurement at a test current up to 27A, with a resolution of 0.01ohms. Frequency range and operating voltage are wide, allowing for a diverse range of applications up to and including CATIV 550V phase-to-phase. Testing commences automatically as soon as the instrument is connected to the supply. Repeat testing is provided by the TEST button. High current loop tester Simple auto start operation 16Hz to 400Hz frequency range Up to CATIV 300V phase-to-earth (550V phase-to-phase) applications Optional two-wire lead set available separately, RS stock no. 537-7282 Voltage measurement range 0 to 550 V Accuracy ±5% ±2V Loop test operating frequencies 16Hz: 15 Hz to 18 Hz 50/60Hz: 40 Hz to 70 Hz 400Hz: 260 Hz to 490 Hz Test currents 550 Vac 230 Vac 115 Vac 50 Vac 20Ω Range & 200Ω Range 27A / 2.7A 12A / 1.2A 6A / 0.6A 3A / 0.3A Loop test accuracy 0 to 19.99 Ω (20Ω range) ±5% ±0.03 Ω 0 to 199.9 Ω (200Ω range) ±5% ±0.5 Ω Size and weight 148 x 203 x 78 (HxWxD, mm), 980g Note RS is an authorised Megger distributor. Purchased though RS this product is eligible for the Megger extended 3 Year warranty Supplied with durable hard carry case; BS1363 mains socket test lead; 8 x AA alkaline batteries; instructions.

Product Detail

New items

LT300, Megger

LT300 Loop Tester The LT300 combines high current-loop testing over a wide range of frequencies and supply voltages with simple operation. This is a HIGH CURRENT ONLY tester, designed for installations where there are no RCDs installed. A two-wire test performs a fast loop impedance measurement at a test current up to 27A, with a resolution of 0.01ohms. Frequency range and operating voltage are wide, allowing for a diverse range of applications up to and including CATIV 550V phase-to-phase. Testing commences automatically as soon as the instrument is connected to the supply. Repeat testing is provided by the TEST button. High current loop tester Simple auto start operation 16Hz to 400Hz frequency range Up to CATIV 300V phase-to-earth (550V phase-to-phase) applications Optional two-wire lead set available separately, RS stock no. 537-7282 Voltage measurement range 0 to 550 V Accuracy ±5% ±2V Loop test operating frequencies 16Hz: 15 Hz to 18 Hz 50/60Hz: 40 Hz to 70 Hz 400Hz: 260 Hz to 490 Hz Test currents 550 Vac 230 Vac 115 Vac 50 Vac 20Ω Range & 200Ω Range 27A / 2.7A 12A / 1.2A 6A / 0.6A 3A / 0.3A Loop test accuracy 0 to 19.99 Ω (20Ω range) ±5% ±0.03 Ω 0 to 199.9 Ω (200Ω range) ±5% ±0.5 Ω Size and weight 148 x 203 x 78 (HxWxD, mm), 980g Note RS is an authorised Megger distributor. Purchased though RS this product is eligible for the Megger extended 3 Year warranty Supplied with durable hard carry case; BS1363 mains socket test lead; 8 x AA alkaline batteries; instructions.

Product Detail

New items

LRCD220, Megger

LRCD220 Loop & RCD Tester The LRCD200 series tester combines an Earth loop impedance tester with an RCD tester. The loop tester is a non-tripping test suitable for systems protected with 30mA or larger RCDs. The RCD testing supports 10mA to 1000mA RCDs with the full range of tests. Ramp testing provides a trip current test for the testing of nuisance tripping RCDs. Suitable for use on 110V or 3 phase supplies.,Designed to meet the tough environment of site work, the instruments are rubber armoured, have a built-in protective front cover, and meet the requirements of BS7671, IEC1010 and BSEN61557. All instruments are IP54 weatherproof. The combined instrument offers all the test functions necessary for live electrical testing requirements, in a simple and cost effective instrument. Built-in protective front cover Tough rubber armoured case Weatherproof to IP54 High current loop testing Phase to phase loop testing Auto RCD testing 1000mA RCD test Phase rotation 110V, 230V and 415V operation Backlit display Note RS is an authorised Megger distributor. Purchased though RS this product is eligible for the Megger extended 3 Year warranty Supplied with Durable hard carry case, instructions, 3 wire test lead with crocodile clips, BS1363 mains socket test lead, 8 off AA alkaline batteries.

Product Detail

New Items

LRCD220-EN-BS, Megger

FC2000, Kewtech Corporation

LTW315-RS-BS, Megger

P06230304, Chauvin Arnoux

P06230301, Chauvin Arnoux

LTW315-EU-BS, Megger

LT300-EN-BS, Megger

LT300, Megger

LRCD220, Megger

FAQs