Discounted Products

GRAVITY I2C 16X2 ARDUINO LCD WI

NSC4-08PG-G02 PLUG(ORANGE) -35MM

Tactile Switch - TSE / TSSE Series Off - momentary switching action Size: 12 x 12 mm Sealed with silicone rubber to IP67 Washable Copper alloy gold plated terminals Insulation resistance: > 1000 MΩ @ 100 Vdc Dielectric strength: 250 Vdc, 50 Hz for 1 minute PA46 / PA6T case Tactile

SH37F-P-4 37-PIN FEMALE TO PIGTA

XFRMR TOROIDAL 1000VA CHAS MOUNT

Selco CA/OA Series Bi-Metallic Thermostats Professional range of CA/OA series thermostats from Selco. These thermostats utilise a temperature sensitive disc, electrically isolated from the switch. The entire switch is enclosed in a dust free housing. Contacts open or close on rise when surface or temperature increases to the snap point of the calibrated bimetal disc. The bimetal disc is retained by a mental heat-conducting end cap. All CA/OA series thermostats are used for various applications and are highly reliable and excellent quality. Thermal Switches

THERMAL PAD 400 12X12 SHEET

Male Connector KQ2H The KQ2H male connector fittings from SMC are quick and easy to install into your pneumatic fittings. These KQ2H male connectors are also more compact in design which means that these connectors can be used within a confined space. Male connectors are designed to pipe a female thread. The new KQ2 range of products are lighter than previous models and have the advantage of improved insertion and removal forces. Can be used under a wide range of pressures from a low vacuum to 1MPa Low force required for fitting and removal Compact dimensions for use within smaller spaces Various port size's available One-touch Unifit versions available Available with thread sealant Thread-to-Tube Adaptors Sealant coated threads minimise assembly time. The fittings can be used on vacuum or positive pressure lines. Suitable for use with nylon, soft nylon or polyurethane tube for compressed air or water (general industry) conveyance Maximum operating pressure 10 bar Maximum vacuum operating pressure -100kPa Proof pressure 3MPa Ambient and fluid temperature -5 to +60°C (water 0 - 40°C) All thread sizes are specified as R(PT) (taper) type

AC/DC WALL MOUNT ADAPTER 5V 15W

Designed specifically for LED applications, this range of Insulated Metal Substrates (IMS) also known as Metal Clad Printed Circuit Boards, are designed to allow better thermal management also allowing for more forward current to LEDs. Whilst being able to maintain die temperatures, this results in more light with the potential to use less LEDs for the end application. Designed from the standard hex star board footprint, boards have a range or Heat Sinks and Thermal Interface Materials for easy, plug and play operations. Compatible LED Families Cree: XHP35, XP-C, XP-E, XP-E2, XP-G, XP-G2, XP-G3, XP-L, XP-L2, XT-E Nichia: NVSL119C, NVSW119C, NVSW219C, NVSL219C, NVSW119B-V1, NVSL119B-V1, NVSW219B-V1, NVSL219B-V1, NCSW119B-V1, NCSL119B-V1 and NCSW219B-V1 LumiLED: Luxeon Q Seoul: Z5, Z5P, Z5M Samsung: LH351D and LH351B LG: H35C4, H35F0, H35A0, H35B0 and H35C0 TSLC: N3535, C3535

Triple Deck with Grounding Provides 3 circuits within the same terminal width and a clamp electrically grounded to the mounting rail Ideal for use in the supply of 3 -phase motors with protection Blocks are closed therefore do not require end section Comb facility eases wiring by being placed in the insulating support and remaining captive when clamp is loosened IP20 protection Approvals 7777

Helagrip PVC Cable Markers On Reels Chevron cut PVC cable markers supplied on reels. The design of the marker allows it to be easily applied over a range of cable sizes. They are manufactured from flexible, high grade PVC which conforms to IEC 684-3. Ideally suited to panel building, mass transit, utilities, telecommunications, and electrical contracting. Features and Benefits • Easily apply one size marker to wide range of cables • Markers are applied pre-termination • Chevron cut to ensure markers lock together • Characters available are 0-9, A-Z, and standard electrical symbols

Strip Brushes Manufactured from black Nylon 6 filament Encased in an electrogalvanised mild steel channel and housed in an extruded mill finished aluminium alloy carrier Operating temperature range -50°C to +100°C and resistant to most common solvents Available in most thicknesses with different filament lengths Easily cut using a hacksaw and bolt cutters (see stock no. 539-069 ) Instructions supplied with the product Supplied in 1 metre lengths Length in Specifications refers to Bristle Length Dimensions (mm) Stock No Angle F H T W Filament Dia 326-9791 180 ° 8.5 6 1 5 0.15 326-9808 90 ° 9.3 6.7 1.2 6.7 0.15 326-9814 180 ° 8 6.3 1 6 0.15 326-9836 180 ° 12.8 7.7 1.3 7.8 0.15 326-9842 90 ° 11 7.9 1.5 7.6 0.15 326-9858 180 ° 13.4 8.1 1.2 7.6 0.15 326-9870 90 ° 11 7.9 1.5 7.6 0.2 326-9886 45 ° 16.5 6.7 1.2 6.5 0.2 326-9820 180 ° 13.4 8.5 1.5 7.6 0.2 326-9892 90 ° 11 7.9 1.5 7.6 0.2 326-9909 180 ° 12.8 7.7 1.3 7.8 0.2 326-9915 90 ° 11 7.9 1.5 7.6 0.2 326-9937 180 ° 20.4 13.6 1.8 12.1 0.4 326-9943 90 ° 19 13 1.5 12 0.4 326-9959 45 ° 25 13.2 1.6 12 0.4 326-9965 180 ° 20.1 13.6 1.8 12.1 0.4 326-9971 90 ° 19 13 1.5 12 0.4 326-9987 180 ° 19.1 13.6 1.8 12.1 0.4 326-9993 90 ° 19 13 1.5 12 0.4 327-0000 180 ° 19.14 13.5 1.5 13.2 0.6 327-0016 180 ° 19.1 13.5 1.5 13.2 0.9

Under the brand name SIRIUS ACT, Siemens offers a unique portfolio of pushbuttons and signaling devices with global product approvals in four modern design lines of rugged genuine metal and high-grade plastic. An innovative snap-on concept makes the task of installing a unit so easy that it can be done with one hand and without any special tools. Groove-free holes are adequate as mounting holes since full twist prevention is already integrated. Thanks to the high degree of protection throughout, the rugged devices are suitable for use in industry and outdoors. Even cleaning with a high-pressure jet is possible. Neither dust, oils, nor caustic solutions can interfere with reliable operation. As well as standard wiring, the devices can also be connected to the controller via PROFINET, AS-Interface or IO-Link. Doing so will help you to reduce wiring time and effort, minimize error sources and have more flexibility. The graphical Online Configurator provides convenient support when selecting and ordering individual devices, enclosures and labels. Extensive documentation (e.g. manual, 3D data, terminal diagram) is available. Note: Single device, please order holders and modules separately.

Institutional Castor - Synthetic, Series 5370 Tente Series 5370 LEVINA single wheel bolt-hole castors are manufactured from high grade synthetic materials that are generally resistant to all detergents and disinfectants currently available. The castors incorporate a double ball bearing precision swivel head, and grey TENTEprene (thermoplastic rubber) non-marking tyre. M10 bolts are included with the LEVINA castors which can be removed without removing the castor wheel. The polypropylene wheel castors can accept a static load of 200kg, and a dynamic load of 100kg. Series 5370 LEVINA castors offer a number of benefits that include the following: Solid castor housing that guarantees long life High quality tread materials ensure exceptional castor rolling properties Short castor brake pedal offers easy operation and smaller swivel radius Smooth surface making the castor design easy to clean Modern castor design enhancing products that they are used with Tente castors provide an optimal balance between application, design and technology. The single-wheel LEVINA castor range offers a high degree of resistance to environments where detergents and disinfectants may pose a problem, making use of high-grade synthetic materials throughout. LEVINA castors are available as solid plug, M10 or M12 threaded plug, or screw plate versions. Bolthole versions are designed to allow the bolts to be inserted separately at a later time. Double-wheel Tente LINEA castors ideally suit hospital and care home beds, where the level of comfort and safety required is of paramount importance. The LINEA castors are unique in offering a design where the wheels are only a fraction below the overall height of the entire castor. The elegant, clean design of the LINEA castors enable them to be fitted to beds and other medical equipment, where the overall height is kept as low as possible, to maintain overall patient comfort.

Carel IR33+ Refrigeration ControllerThe IR33+ smart refrigeration controllers are designed specifically for the refrigeration installer as they enable selection from a range of pre-loaded applications, eliminating the need to program the controller parameters. IR33+ is the evolved series of the IR33, meaning this retains all of the functionality and diversity but in a refined Refrigeration Controller.Benefits of the IR33+ seriesInherits all features of the IR33 series with increased flexibilityNo programming required4 pre-loaded configurationsNTC & PTC thermistor probe inputs availableVarious relay output configurations available16A compressor outputInfrared receiver and buzzer12 to 24V AC & 115 to 230V AC poweredRS-485 serial connectionIP65 enclosurePlug-in terminalsFront panel mounting systemIR33+ refinementsTouch keypad added giving a completely flat surface for improved hygiene which complies to HACCPNew button layout for added user-efficiencyBrighter display available in green, red, white and blue accompanied by a 30% increased screen size over the IR33Intuitive user interface for ON/OFF, buzzer muting directly and dedicated alarm iconsBrowsing messages in context to the area on displayAutomatic recognition of Modbus and CAREL protocols as standard across the IR33+IR33 Smart Refrigeration Controllers

Galvanised Steel Galvanised perforated sheet Can be painted after degreasing Selvedged border configuration -5mm/+10 mm on width and length Dimensions (mm) Pattern Hole(mm) Open Area Pitch I (mm) Pitch II (mm) Hole Configeration 1 1.2 ø 42% 1.7 3.2 60° 2 1.5 ø 22% 4 4 45° 3 1.7 ø 45% 2.4 4.1 60° 4 2.0 ø 47% 2.8 4.8 60° 5 3.0 ø 33% 5 8.7 60° 6a 3.0 ø 51% 4 6.9 60° 6 4.8 ø 50% 6.5 11.2 60° 7 6.4 ø 43% 9.2 16 60° 8 8.0 ø 68% 9.2 16 60° 9 6.0 x 6.0 62% 7.6 7.6 Square 10 6.0 x 6.0 52% 9.1 7.6 Staggered 11 4.7 x 4.7 35% 8 8 Square 12 2.4 x 12.7 34% 4.8 15.1 Rect 13 6.0 A/F 79% 6.76 11.63 Hex 14 10.0 x 10.0 59% 13 13 Square 15 1.0 ø 46% 1.4 2.4 60°

Lifeline 4 Rope Pull Switch The Lifeline 4 rope pull switch, also known as a cable pull switch or grab wire switch, can be installed along or around awkward machinery such as conveyors and provides constant emergency stop access. The positive mode mechanism helps ensure that the contacts are immediately latched open on actuation and can only be reset by the intentional action of turning the blue reset knob. The design of this safety switch also protects against nuisance tripping and the effects of thermal expansion. A mushroom head emergency stop button is included on the Lifeline 4 to provide E-Stop access even at the extreme ends of the span. The cable status indicator makes this rope pull switch easy to set up and maintain for spans up to 125m. Switches up to 125m span Universal mounting and operation Lid mounted emergency stop button, designed to conform to ISO 850 Switch lockout on cable pulled and cable slack Cable status indicator on switch lid Sealed to IP66 Tension force 188 N lock-out, 103 N running Operating Force Operating temperature -25°C to +80°C Safety contact gap >2 x 2mm Rated at 500V ac/1A, 250V ac/2A, 100V ac 5A Heavy duty weatherproof die-cast aluminium alloy (LM24) yellow case Stainless steel eye nut, glass filled nylon indicator CE marked in compliance to relevant European Directives Note For suitable rope kits see stock no. 366-3878 typically. Approvals BG, UL listed for Canada and US. Standards Designed to conform to EN418, EN292, EN60947-5-1, ISO 13850, BS 5304.

V Series Sealed Contura Rocker Switches Carling Technologies V Series Contura snap-in rocker switches offer unique options including choices for ratings, circuits, colours, illuminations and symbols. The V series switches feature removable actuators in a choice of actuator styles and colours, and can be illuminated with either square or bar shaped lenses. The Contura switches with sealed option, are certified to IP66 and IP68, signifying complete protection against dust and prolonged spray and submersion under pressure, and are vibration, shock, thermoshock, moisture and salt spray resistant. Dual seal protection. Interchangeable actuators. Certified to IP66 and IP68 for front panel components. Vibration, shock, thermoshock, moisture and salt spray resistant. Temperature range from -40°C to +85°C. Carling Technologies® Rocker Switches

Natural Insertion Rubber Natural rubber sheet with an insertion of polyester fabric to give improved properties Polyester fabric insertion Sheets up to 3mm thick are single ply Sheets over 3mm thick are two ply Sheet size 1000 x 600mm Material Natural Rubber Colour Black/Tan Animal/Vegetable Oil No Ethylene Glycol Yes Oils & Fuels Yes Dilute Acid/Alkali Yes Hot/Cold Water Yes

IP68 Deltron 486 Series Diecast Aluminium Boxes Lid is designed to give maximum seal face and minimum exposure Lid supplied with stainless steel (SS304) M6 x 25mm long captive screws 3mm one piece die cut silicone rubber sponge seal (01-255FR) with self adhesive backing (01-255SAB), suitable for-60 to 240°C Minimum seal thickness and seal frame width 3.5mm Minimum enclosure wall and lid thickness 3mm Integrated PCB guides and standoffs Integrated earth fixing points and is supplied with brass shake proof screws Note MPNs that have the suffix 486-xxxxxx-66 are sealed to BS EN 60529:1992 IP66 / IP67 MPNs that have the suffix 486-xxxxxx-68 are sealed to BS EN 60529:1992 IP67 / IP68 (10mtrs for 20 hours)

Rapid Cure Epoxy Adhesive, 5 Minute ® Fast curing clear epoxy adhesive 4 minute pot life 93°C maximum operating temperature Works down to -40°C when cured ITW Devcon Structural Adhesives Two-part structural adhesives and dispensing systems which allows the metering, mixing and accurate application of epoxy and acrylic structural adhesives. They ensure accurate ratio mix, fast application with a predetermined flow rate and reduced waste/mess. To apply the adhesive a system of a 1:1 ratio cartridge (in 3 sizes) application gun and static mixing nozzle is required; each is available separately.

Thread repair kit - HELICOIL® plus M2.5 - M6 HELICOIL® plus for recovery and repair of a damaged thread. HELICOIL® plus is flexible and can be fitted wherever a screw may be placed. Set supplied with: different lengths and dimensions of HELICOIL® plus threaded inserts, drill bits, HSS manual threads, manual pins, tang breakers. Green colour to check the thread is present after fitting. Thread Pitch No. of threaded inserts M 2.5 x 2.5 0.45 20 M 2.5 x 3.75 0.45 20 M 2.5 x 5.0 0.45 20 M 3 x 3 0.5 20 M 3 x 4.5 0.5 20 M 3 x 6 0.5 20 M 4 x 4 0.7 20 M 4 x 6 0.7 20 M 4 x 8 0.7 20 M 5 x 5 0.8 20 M 5 x 7.5 0.8 20 M 5 x 10 0.8 20 M 6 x 6 1 20 M 6 x 9 1 20 M 6 x 12 1 20

The Keysight Technologies 11716A quickly and conveniently connect 1 dB step and 10 dB step attenuators together to achieve greater dynamic range with 1 dB steps. The Keysight 11716A interconnect kit contains a rigid RF cable, mounting bracket, and necessary hardware to connect any pair of Keysight 8494 or 5 or 6 or 7 attenuators in series. Attenuators must be ordered separately. Provides wide attenuation range with 1 dB steps Connects any pair of Keysight 8494 or 5 or 6 or 7 attenuators in series

The Rockwell Automation Multi-Function Timing Relay has SPDT contact arrangement with 0.050 seconds to 9999 hours timing range. It is NEMA B300 and NEMA 4/IP66 rated. Socket or panel-mounted It is environmentally friendly